Lokar Automatic Trans Mount Shifter TH400 User Manual

Browse online or download User Manual for For the car Lokar Automatic Trans Mount Shifter TH400. Lokar Automatic Trans Mount Shifter TH400 User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 6
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Building American Quality… With A Lifetime Warranty!
General Installation Notes:
Please read instructions completely before beginning installation. If you have
any questions please call.
Before starting installation, use wheel chocks to block the vehicle's wheels.
Disconnect the negative battery cable before beginning installation.
Make sure the engine, transmission, body and frame are properly grounded.
Refer to Fig. 1 for the component names.
Tools and Materials Required:
•StandardAllenwrenches:1/8",5/32",3/16",7/32"
•WrenchorSocketSizes:5/16",3/8",7/16",1/2",9/16",5/8",7/8"
•TapeMeasure
•Metalcuttingtool,suchasahacksaworadiegrinderwithacut-offwheel
•Ohmmeter
•Wirecutters/strippers
•Wirecrimpingorsolderingtools
•Bluethreadlockingcompound
Lokar Shifters are designed to fit specific transmissions. Before installing the shifter,
verify that you have the proper model for your transmission. If your shifter does not
seem to fit properly, do not make modifications during installation as this may void
your warranty. Call for assistance.
Verify that the shifter length you have purchased is what you actually want. When
installed, the bottom of the shifter lever will be approximately 3-1/2" - 4" above the
transmission case. From that point up to the top of the knob is how the shifter length
is determined.
Before attempting to make any adjustments, the shifter must be installed on the
transmission and the transmission should be installed into the vehicle.
The shifter is designed to lock in Park and in Neutral. You must depress the release
button in the top of the shifter knob in order to shift out of Park or Neutral. The release
button will only be flush with the top of the knob when the shifter is in Park or Neutral.
To shift from Park directly to Drive, depress the release button and then hold it down
while moving the shifter lever, and the shifter will automatically stop in the Drive
position. Once you release the button, then the shifter will allow you to move the lever
into 2nd gear. You must depress the button again to shift down into 1st gear.
These instructions assume that you have full access to the transmission when the
shifter installation is begun, with the transmission removed from the vehicle, or the
vehicle body removed from the chassis.
TOLL FREE 1-877-469-7440 • [email protected] • www.lokar.com
®
TH400 Automatic Trans Mount Shifter
Installation Instructions
TH400 Automatic Trans Mount Shifter
Installation Instructions
INS0080 Rev. 05/09/14
Page 1
© 2005 Lokar, Inc.
Fig. 1
Shifter
Lever
Shifter
Assembly
Shifter
Knob
Right Side
Bracket
Optional Handbrake
Mounting Location
Main
Plate
Rod
End
Rod
End
1/4"-28 x 1" Button Head
Bolt with Flat Washer and
Nylock Nut
1/4"-28 x 1" Button Head
Bolt with Flat Washer and
Nylock Nut
3/8"-24 x 1" Tension Set
Screws and Jam Nuts
3/8"-16 x 1-1/4"
Button Head Bolts
& Lock Washers
Rear Mounting
Bracket
5/16"-24 x 1/2"
Button Head Bolts
and Lock Washers
5/16"-24 x 5/8" Tension Set
Screws with Jam Nuts
Side Mounting Buttons
Trans
Gear
Lever
Left Side
Bracket
Aluminum
Adjuster Plug
Quad
Lever
Threaded Rod with
1/4"-28 Jam Nuts
Release Button
Page view 0
1 2 3 4 5 6

Summary of Contents

Page 1 - Installation Instructions

Building American Quality… With A Lifetime Warranty!General Installation Notes: Please read instructions completely before beginning installation. If

Page 2 - © 2005 Lokar, Inc

Page 2© 2005 Lokar, Inc.Fig. 3Step 1: If your vehicle already has a shifter of any type installed, disconnect all shifter linkage and remove the shif

Page 3

Step 8: (Continued) Transfer that measurement to the transmission (or to the engine/transmission assembly if the engine is not installed in the vehic

Page 4 - INS0080 Rev. 05/09/14

INS0080 Rev. 05/09/14Page 4Step 11: Put the shifter into the Park position and check the position of the quad lever. It will need to be pointing to

Page 5

INS0080 Rev. 05/09/14Page 5© 2005 Lokar, Inc.Step 15: Check the adjustment of the shifter by placing the shifter all the way forward into the Park p

Page 6

INS0080 Rev. 05/09/14Page 6© 2005 Lokar, Inc.Neutral Safety Switch Adjustment and WiringStep 16: For the neutral safety switch to function properly,

Comments to this Manuals

No comments