Lokar Column Shift Linkage For Ford AOD, 4R70W, and AODE User Manual

Browse online or download User Manual for For the car Lokar Column Shift Linkage For Ford AOD, 4R70W, and AODE. Lokar Column Shift Linkage For Ford AOD, 4R70W, and AODE User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 4
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Building American Quality… With A Lifetime Warranty!
General Installation Notes:
Please read instructions completely before beginning installation. If you have
any questions, please do not hesitate to call.
Before starting installation, set parking brake and scotch vehicle wheels to
avoid accidental movement of the vehicle. Disconnect the negative battery
cable before starting installation.
AOD applications also require the installation of a Lokar Kickdown Kit, available sepa-
rately.
The Lokar column shift linkage is universal, and the stainless steel rod is designed
to be cut-to-fit for individual applications. The kit comes with a 21" long rod, and a
26" long rod is also available.
Refer to Fig. 1, 2 and 3 for the part names.
NOTE: It will be much easier to install the new selector shaft before the transmis-
sion is installed in the vehicle, if possible.
The AOD (non-computer controlled) transmission has a Throttle Valve (T.V.) shaft
that passes through the center of the selector shaft. Parts of these instructions and
some of the photos will refer to the T.V. shaft, a T.V. lever, and a T.V. spring. These
parts are not present in an AODE or 4R70W transmission.
Step 1: Put the shifter and the selector shaft on the transmission into the park
position. Remove any existing linkage from the selector shaft and from the
steering column.
Step 2: AOD Only: Remove the nut and T.V. lever from the T.V. shaft in the center
of the selector shaft.
AODE and 4R70W Only: Remove the bolt or nut from the center of the
selector shaft, and remove the original trans arm. NOTE: If the new Lokar
flange fits on your existing selector shaft, it is not necessary to replace the
existing selector shaft. If you are only installing the Lokar Selector Shaft
Flange and Arm and are not replacing the selector shaft, skip to Step 13.
Step 3: Drain the transmission fluid and remove the transmission pan and filter.
Step 4: Remove the 1/8" diameter roll pin that is located just inside the pan rail on
the boss that the selector shaft slides through. The pin protrudes about 1/8"
beyond the boss. Use a pair of side cutters to grab the roll pin and pry the
pin out using the case as your leverage point. Fig. 4
Step 5: Remove the roller spring that holds the gear selector plate in each gear
position. Fig. 5
Step 6: AOD Only: There is a small spring that keeps tension on the T.V. shaft.
Make sure to pay attention to how this spring is positioned, because it will
likely slip out of place during this step.
TOLL FREE 1-877-469-7440 • (865) 966-2269 • FAX (865) 671-1999 [email protected] • www.lokar.com
®
Column Shift Linkage Installation Instructions
For Ford AOD, 4R70W, and AODE
Column Shift Linkage Installation Instructions
For Ford AOD, 4R70W, and AODE
INS0061 Rev. 04/28/14
Page 1
© 2014 Lokar, Inc.
Fig. 1
Fig. 2
Stainless Steel Rod
AOD Only
Selector Shaft
Trans Arm
T.V. Seal
#8-32 x 3/8" Button
Head Bolts and
Lock Washers
5/16" Female Rod End
5/16"-24 x 1-1/2" Bolt with Washers,
Delrin Bushings, and Nylock Nut
5/16"-24 x 1-1/4" Bolt with Washers,
Delrin Bushings, and Nylock Nut
Hex Connector with Set Screws,
Jam Nut, and 5/16" Female Rod End
Fig. 3
AODE and 4R70W
#8-32 x 3/8"
Button Head
Bolts and Lock
Washers
3/8"-16 x 3/4"
Lock Bolt
Trans Arm
Selector Shaft
Flange
Selector Shaft
(installation not required for models
with factory bolt-on trans arms)
Page view 0
1 2 3 4

Summary of Contents

Page 1 - For Ford AOD, 4R70W, and AODE

Building American Quality… With A Lifetime Warranty!General Installation Notes: Please read instructions completely before beginning installation. If

Page 2 - Fig. 6 Fig. 7

Page 2© 2014 Lokar, Inc.Fig. 5Fig. 4Fig. 6 Fig. 7AOD shown in all photos below. AODE & 4R70W are similar.Example of misaligned Internal T.V. Lever

Page 3 - Fig. 10 Fig. 11

Page 3Step 13: AODE and 4R70W Only: Install the new Lokar flange onto the selector shaft. If using the original selector shaft, use the origi-nal nut

Page 4 - AOD Only

INS0061 Rev. 04/28/14Page 439612Transmission (not included)AODE, 4R70W OnlyAOD OnlySteering Column Arm (not included)Delrin® BushingDelrin® Bushing5/

Comments to this Manuals

No comments