Lokar Automatic Transmission Shifter GM Tailmount User Manual

Browse online or download User Manual for For the car Lokar Automatic Transmission Shifter GM Tailmount. Lokar Automatic Transmission Shifter GM Tailmount User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 6
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Building American Quality… With A Lifetime Warranty!
General Installation Notes:
Please read these instructions completely before beginning the installation. If
you have any questions please call.
Before beginning the installation, disconnect the negative battery cable and use
wheel chocks to block the vehicle's wheels.
Make sure the engine, transmission, and frame are properly grounded.
Refer to Fig. 1 for the component names.
Tools and Materials Required:
•StandardAllenwrenches:1/8",5/32",3/16",7/32"
•WrenchorSocketSizes:5/16",3/8",7/16",1/2",9/16",5/8",7/8",
13mm(metrictransmissionsonly)
•TapeMeasure
•Metalcuttingtool,suchasahacksaworadiegrinderwithacut-offwheel
•Ohmmeter
•Wirecutters/strippers
•Wirecrimpingorsolderingtools
•Bluethreadlockingcompound
Lokar Shifters are designed to fit specific transmissions. Before installing the shifter,
verify that you have the proper model for your transmission. If your shifter does not
seem to fit properly, do not make modifications during installation as this may void
your warranty. Call for assistance.
Verify that the shifter length you have purchased is what you actually want. When
installed, the bottom of the shifter lever will be approximately 4" above the tail
housing bolts. From that point up to the top of the knob is how the shifter length is
determined.
Before attempting to make any adjustments, the shifter must be installed on the
transmission and the transmission should be installed into the vehicle.
The shifter is designed to lock in Park and in Neutral. You must depress the release
button in the top of the shifter knob in order to shift out of Park or Neutral. The
release button will only be flush with the top of the shift knob when the shifter is in
Park or Neutral.
To shift from Park directly to Drive (or Overdrive), depress the release button and
then hold it down while moving the shifter lever, and the shifter will automatically
stop in the Drive (or Overdrive) position. Once you release the button, then the shifter
will allow you to move the lever into the next lower gear. You must depress the
button again to shift down again.
These instructions assume that you have full access to the transmission when the
shifter installation is begun, with the transmission removed from the vehicle, or the
vehicle body removed from the chassis.
TOLL FREE 1-877-469-7440 • [email protected] • www.lokar.com
®
GM Tailmount Automatic Transmission Shifter
Installation Instructions
GM Tailmount Automatic Transmission Shifter
Installation Instructions
INS0099 Rev. 06/24/14
Page 1
© 2007 Lokar, Inc.
Fig. 1
Tailmount Bracket
(6-Bolt Tailhousings only)
Shifter Lever
Release Button
Spacers
Rod Ends
Aluminum
Adjuster Plug
Threaded Rod with
1/4"-28 Jam Nuts
Tailmount Bracket (4-Bolt Tailhousings)
3/8"-16 x 1-3/4"
Button Head Bolts
with Lock Washers
5/16"-24 x 1/2"
Button Head Bolts
with Lock Washers
M10 x 45mm
Button Head Bolts
with Lock Washers
1/4"-28 x 1" Button Head Bolts
with Flat Washers and Nylock Nuts
Quad
Lever
Trans Gear
Lever
Page view 0
1 2 3 4 5 6

Summary of Contents

Page 1 - Installation Instructions

Building American Quality… With A Lifetime Warranty!General Installation Notes: Please read these instructions completely before beginning the install

Page 2 - © 2007 Lokar, Inc

Page 2© 2007 Lokar, Inc.Step 1: If your vehicle already has a shifter of any type installed, disconnect all shifter linkage and remove the shifter an

Page 3

Step 11: Make sure that a jam nut is still present on each end of the threaded rod, and install a rod end onto each end of the threaded rod. Attach t

Page 4 - Fig. 7 Fig. 8

INS0099 Rev. 06/24/14Page 4Fig. 5 Fig. 6Fig. 7 Fig. 8The Button Head Bolt can be installed from either direction, but make sure the Rod End is sandwi

Page 5 - INS0099 Rev. 06/24/14

INS0099 Rev. 06/24/14Page 5© 2007 Lokar, Inc.Neutral Safety Switch Adjustment and WiringStep 13: For the neutral safety switch to function properly,

Page 6

INS0099 Rev. 06/24/14Page 6© 2007 Lokar, Inc.Fig. 11For shifters manufactured 1994 and earlier, please contact Lokar for assistance.To Remove Shifter

Comments to this Manuals

No comments